Univivi IR Illuminator 90 Degree Wide Angle 8-LEDs IR Infrared Light 850nm Infrared Illuminator for Night Vision IP67 Waterproof Outdoor for Security Cameras

Using it for VR. Helps improve tracking in low light areas.

For over a year now I have been experimenting with inexpensive 850nm near-infrared illuminators for use as NIR therapy devices. The results have been surprisingly positive. These devices have actually helped everyone who has tried them – in some cases quite impressively. Over time I became increasingly dissatisfied with my lack of knowledge of what these devices were actually doing, so I purchased a TES 1333 Solar Power Meter to measure irradiance (W/m^2 of infrared energy output) and a high quality multimeter to measure current draw. Due to the “granularity” caused by the spacing between LEDs it is not possible to get accurate measurements of irradiance directly agains the glass face plate of these devices, and the UNIVIVI U8R is especially chunky in this regard. So I took irradiance measurements starting 2” from the glass where the light beams have spread and blended together and at 2” intervals out to 12” and entered the resulting data points into a graphing calculator. Because irradiance diminishes with the square of the distance from the source, I assumed a quadratric regression curve could be closely fitted to this set of points. An R^2 of 0.984 for the resulting equation confirmed my fondest hopes. All this mathematical jiggery-pokery makes it possible to calculate an accurate irradiance value at zero distance from the glass. This is useful, because this value represents the true power density of the device. By popping the back cover off an inline rocker switch I was able to expose contacts for my multimeter to measure current flow. Set the switch in the OFF position, set up the multimeter, touch the exposed leads with the probes. The light comes on and the the current in amps gets measured. The transformer supplies 12DC current, so volts x amps = Watts. I am going to the trouble of spelling out how I did all this because ignorance, speculation, and seller misinformation abound in relation to all of the products in this class. So how does the little UNIVIVI U8R do? IT DOES FANTASTIC! The calculated irradiance at zero distance was right at 1000W/m^2 or 100mW/cm^2. 100mW/cm^2 is a seriously therapeutic dose rate, and you will get it if you put the glass screen directly against a body part. The unit is nominally rated at 8W, but mine drew 0.88 amps which works out to an actual 10.56W power draw which is impressive. So much for nominal ratings. (But I did not check to see if the transformer was actually delivering a full 12V DC. Another day for that.) So, I was pleasantly surprised by this little guy. It comes with a 1 amp power supply, and its light sensitive “eye” is external so you can put a piece of tape over it without having to disassemble anything so you can use it in daylight. It is light and easy to handle and sized just about right for treating hands, knees, neck or other localized areas. It also represents an excellent value on a total NIR energy delivered per dollar cost basis for whatever purpose you might want to use it for. It’s good gear in my book!

I bought two of those for extra redundancy just to run my PSVR2 without having to turn on every light like its full daylight. Now I can just drive at night in the dark like a regular person. I set these lights ups more or less at a 45° from the front of my sim racing rig. The faint red glow is barely noticeable. My PSVR2 goggles work perfectly as if the room is lit up bright.

UPDATE: The IR Illuminator works very well, however the 1 amp power supply is undersized and likely to fail. When this happens the LEDs will become power starved and begin to blink or fail to light. I have four of these and two began to blink the same week. I have upgraded to a 2 amp adapter of slightly larger dimensions. It is a 12-volt 2-amp SANSUN UNIVERSAL AC ADAPTER that runs about $7 here on Amazon. It runs cooler and seems to light a tad brighter at 12.2 volts under load. Will update if there are further issues but the illumination provided is a big boost to the quality of security camera images. ORIGINALLY: I have a Swann 4K Camera system and added this to an area that needed additional night illumination. It's important to note that although the directions state that the Illuminator should be mounted close to the camera and aimed in the same direction, this is not a requirement. It can be mounted closer to an area needing supplemental lighting further away or from the side. It is illuminating a wider area than expected and a 2nd camera on another side of the house is picking up some of the additional light. It is a solidly built product, easy to mount and connect.

It helped my outdoor camera see further at night, it really added a large area that I couldn't see before