SUNLU High Toughness 3D Printer Resin, Enhanced Flexible 3D Printing Photopolymer Resin, 405nm UV Fast Curing 3D Resin for Most LCD DLP SLA Resin 3D Printers, Bendable and not Brittle, 1KG Grey

This resin is awesome. It comes out a little flexible, yet still very hard. The miniatures I printed have been much more durable than ABS-tenacious mix, and there are no issues with supports failing. So you get flexibility AND strong supports. And it's also very reasonably priced! I think I'll just use this from now on for all of my miniatures

The media could not be loaded.  Long story short this is my new favorite resin.I'm not sponsored in any way (which is hard to find these days on Amazon reviews. I'm just so surprised I had to let people know)Previously I used a 1/4 mixture of tenacious to abs like sirayatech resin to achieve less brittle miniatures for wargaming and ttrpgs.This resin didn't have to be mixed, is actually a bit cheaper, but most importantly prints better. It took very little time to tune the exposure to a setting that worked so it's more forgiving than other resins I've used.Prints easily came out of their supports with minimum effort. The tenacious/abs like mix often had to be removed with hobby cutters.Durability; the models I printed were very flexible. Swords, staffs, chains etc on my miniatures and even after curing are still pretty flexible. I've already dropped some pieces and had my toddler run off with another and they handled great.*** As a wargamer this was the most important quality for me. They have to survive the occasional drop, bump, or toss from one house to another.Finally the detail came through strong on my 8k printer, but I still have some slight adjustments to make. I'm going to start ordering by the 2kg bottles for sure!If you have any doubts, try it! I got my bottle for 30 USD, which is cheaper than the mixture I used before. You won't regret it.

This resin is probably tied for 2nd in my top three line up. The durability is outstanding and for miniatures with arms separate from torsos but connected by a weapon or prop that additional flexibility makes a difference in preserving your sanity when assembling your minis. I print at .04 layer height for 2.8 seconds per exposure and the only print fails I had were my own fault due to lack of planning. I feel that detail is slightly less crisp with this resin than with my other preferred brand but still a step above the normal board game quality. I will def use this resin again.

This resin is the best resin for miniatures I've used. Crisp detail and not brittle. A little bendy at the start, but firms up nicely after a few days. 1L, no print failures, every model perfect. Printed on an Elegoo Saturn 3 12k at 0.03 layer height, the miniatures look as good as the preview pics of the stl's.

Great for miniatures the details Hold up great even on small pieces like a needle on a syringe did several drop tests and breaking only occurred after several 5 ft drops onto hard surfaces. using 1.65s on .025 layers on a Saturn 3 ultra i see no layer lines no delamination the only failures were due to using the new voxel dance software and tuning support settings. i wont be switching resins unless something significantly better comes along that can make minis that survive being handled and played with by small kids and doesn't cost $65 per 1kg

I have tried quite a few resins, the manufacturer's brand, Elegoo, Chitu, and Conjure. Then I saw someone in the forums say Sunluu was the way to go and I have never looked back. If you want to print dnd minis and not have all the swords and bunny ears snap off, this is the one you want. I've probably done 20kg of it at this point. The formula doesn't seem to drift so topping bottles off from an almost done one is totally fine. Bottle shape is so much better for shaking things, you can really get both hands on it and give it a whirl. The resin absolutely will separate after a few days in the vat without printing but at least you can see it split to grey stuff and oil stuff. Always still that vat with a silicone brush or something if it's been sitting there, and give those bottles a good shake before you poor. With the toughness resin, most pre-supported patreon models you can basically just rip out of the supports, if you do it soon after printing, don't have to be careful or use snippers. Saves so much time. If you don't get back to your prints for awhile and they have air dried for a few days then be a little more careful getting the supports off, but otherwise, this resin is the way to go.

Amazing resin. Flexible when printed thin but still totally sandable. A little pricy but well worth it.

Not Bad For Its Price. Its Good

Ich habe mit dem Elegoo Mars 4 DLP fantastische Ergebnisse erhalten ... Das Rein Profil habe ich in LycheeSlicer hinterlegt. Es bietet bei 2,5s Belichtungszeit eine optimale Haftung bzw. Stabilität. Fehldrucke sind ausschließlich durch fehlende Supports oder an einer zu geringen Umgebungstemperatur zurückzuführen.Achtet darauf ausschließlich bei 25°C + zu drucken.Supports hinterlassen auch so gut wie keine Rückstände. Sollte dies der Fall sein kann oder vielmehr sollte vor dem Curing/Aushärten die Stellen bearbeitet werden. Eine Bearbeitung nach dem Aushärten ist aufwendiger.Der Endzustand ist sehr robust und es eignet sich für mich als Tabletop Hobby Typ ideal für meine Miniaturen. Es ist auch wirklich Robust, da mir der Drache runtergefallen ist ... Aber keine Bruchstelle aus 1,5m Höhe.Habe mir gleich weitere 2Kg bestellt.

Très bonne qualité pour sont prix.

Used on elegoo Saturn 3 ultra resin colour white.Calibration cones gave a exposure time of 2.4 seconds.No issues experienced with printed models.Excessive exposure to IPA can make the prints less ridged so no more than 1 minute during clean up recommended.Thoroughly dry before curing👍.Made wheels for RC car which I race.No cracks or deformation yet even after some horrific crashes🙈Great value for moneyJust purchased more but in black this time.😁

Flexible y resistente, la comprè para imprimir muñecos para niños y parece ser el producto perfecto para esta funcion. He impreso tb algunas miniaturas para wargame y no he notado diferencias en los detalles comparando con la resina normal. Es un poco cara para usarla come unica resina, intentarè mezclarla con otras y a ver como sale

maleable y resistente mejores prestaciones que la normal.