CCTREE Creality3d CR-10S DIY Desktop 3D Printer Kit Large Printing Size 300x300x400mm 1.75mm 0.4mm Nozzle with Filament Detector and The Dual Z Axis

The media could not be loaded. It took me a while to finally buy a 3D printer since it was a lot more of a want then a need. After allot of research I decided to go with this guy as my first ever printer. WORTH IT. This thing is amazing, strong durable design, allot of upgrades from there older version and work amazingly. This is classified as a DIY printer since some assembly is required and it is extremely mod-able. You can buy and print many parts to change and improve the printer for your need.But right out of the box this set up easy and worked immediately with wonderful quality and I barely knew what I was doing yet.My glass print bed as many others have said was a little warped, only noticeable because with printing you are playing with decimal levels of milometers. I found swapping it with cheap mirror tiles from home depot did the trick. I didn't notice or care about this until I really started getting picky with my prints. Everything else was excellent quality right off the bat.I have now done hundreds of hours of printing and haven't had a single part fail on me, only changing heat tips(which it comes with a good amount of) and adding fun little mods(not what i'm reviewing here) this printer is straight up wonderful.The price is comparable when viewing other models of printers and was well worth it. Though I would'n't say this is an "entry level" printer because it has such a large print bed and so much potential. But trust me if you go cheaper and smaller at first you will only ending up wanting to buy bigger and better, like this one, spending more in the long run, so it is worth it!

kids opened for Christmas, went through full online setup and checked all parts and screws. did have minor adjustments but normal. was able to print a few items before filament flow had issues and extruder stepper motor started to make noise and failed (HatchBox PLA at 205c tip, 50c bed). Swapped extruder stepper motor line with x,y and z cables and extruder stepper motor would work with loud grinding noise. If hooked extruder cable to x,y or z stepper motor it would not move axis so extruder cable not sending inputs. It appears an issue in extruder stepper motor may have messed up circuit on controller board or issue with controller board caused extruder motor to fail, Can get all stepper motors to work except extruder stepper motor now making loud grind noise when getting input from X,Y of Z cable input (swaped cable to test). Not sure if should return whole unit or if just replace extruder stepper motor and control board. Shipped fast and worked great at first, will see if we can fix issue and get unit up and going or if just need to return, Hope to get resolved and will update once get figured out. Would like to say it did ship fast and liked the extra tips and bed mat. When unit worked it was quieter than other printers I have played with and print quality was nice when CR-10S first worked. Used Cura and IdeaMaker for slicers.Update: checked voltage and ohms on Stepper motor Control board, looks like bad Stepper motor on extruder caused control board to fail. Hope to get new board and stepper motor or replacement unit. Will update after hear from customer Support.Update 01-08-18:Support contacted and had parts in my hand within 2 days, have to say customer service was great! Unit up and running within few hours of installing, prints getting dialed back in again. Would like to say thank you to Jenn for her efforts and help during holidays.Glad to see they stand by their products and customers, would recommend from this seller.

Terrible. Mine came with multiple issues.1-bowed glass and bed2-x axis is all our of wack and was off my 5mm on the right side and anytime I would adjust it it would go right back3- pretty much every wheel was over tightened on deliver and had flat spots4-hot end blower fan had one scree over tightened and the plastic housing was snapped so it rattled very loud5- x axis right tensioner is bent causing the belt to rub.6- the main control unit turned off randomly on my initial test prints 2 times.7- after messing with this thing and seeing how much money it would cost to fix all the issues I started my refund here on Amazon. It better go well. This is completely unacceptable.It also had a very hard time even keeping a constant temp on the bed and hot end. I could go on I'm sure.

This is a decent little printer out of the box. With a few upgrades, it can be little beast of a printer. A little bet of setup is required, but not hard at all. Its the same CR-10s that Ive seen before, but I decided to buy from CCTREE because of the extra nozzles they throw in and the build plate sticker. Also, the printing sticker works quite well once everything is adjusted. The reason for the 4 star and not a 5 star review is that some of the rollers and the Z -axis was loose and needed tightening, also the glass sheet does come uneven, I'm looking to get a mirror or borosilicate glass to print on. Ive seen other re-sellers fix these issues before selling, but i would still buy from them again(as its not to hard to fix these issues). .