StarTech.com M.2 SATA SSD to 2.5" SATA Adapter [NOT NVMe], Open-Frame Bracket, 7mm High, M2 Hard Drive Adapter - TAA

Purchased to clone my current laptop's SSD to a bigger capacity, using the laptop's 2.5 inch HDD tray. It did the work flawlessly. The new SSD was Samsung 860 EVO M.2 500GB. A few notes though, small details but maybe useful for someone. Pros: this adapter supports NOT FORMATTED (not allocated) disks, which is a big plus! Per my knowledge, none of the current m.2 to USB adapters support not-formatted SSDs, which means you have to remove your current SSD, install the new one, format it, remove, reinstall original SSD, only then the new SSD can be used with a USB adapter, rather inconvenient procedure. This was one of reasons I purchased this specific adapter. And it worked just fine, the cloning software identified the new SSD adapter as a non-allocated disk and cloned right away. The PCB, soldering, assembly of the adapter, metal rails show a good quality, not some cheap crap that I usually see at this price range. Cons: 1. The adapter is kind of mirrored/reversed, the power and data sockets are at the reverse side compared to a standard 2.5 inch HDD/SSD sockets. In desktops it may not be an issue as power/data cables are separate and you can install the adapter the way you want to for SSD's optimal heat dissipation. In laptops though, most of the time 2.5 inch drives are installed the aluminum cover looking outside (PCB side inside) of the laptop, and only one combo cable is attached which usually cannot be reversed. Example: Dell inspiron 7559 laptop. The only way this adapter gets into the 2.5 inch bay, is with SSD facing inside the laptop which is not good for heat dissipation at all. No way I could install it SSD facing outside as the laptop connector is right-angle and cannot be flipped. Just compare the connectors location of the adapter to any 2.5 HDD connectors, you'll get the point. This should be considered if you're worried about SSD cooling using thermal pads etc. 2. The mount and screw for 2280 SSD protrudes from the adapter edge by about a millimeter, causing the laptop's HDD bracket to be bent slightly to fit the adapter. You don't get a flush edge which is kind of upsetting, but it did not cause issues fitting in the bay. If your laptop SSD bracket is not flexible enough, you may have issues installing this with 2280-long SSDs. Wish the manufacturer placed the SSD connector 1mm further inwards, so that the mount did not go beyond the edge and would sit flush. Overall, an excellent product and well deserved 5 stars if you do cloning, or install in desktop. For permanent install I'd give 4 stars because of heat dissipation issue due to reverse install in some laptops. Something to consider depending on your application.

Have a WD SA500 M.2 SSD, needed to mount it in a 2.5 inch drive slot because I don't have an M.2 PCIe/NVMe slot. It was plug-and-play, no drivers, worked with Win10 and MacOS. This kit has 1 M.2 slot, and metal rails to mount perfectly as a replacement for a slim-line (7mm height) 2.5 inch SATA drive. Can also be mounted in place of a 3.5" SATA if you add a 2.5 to 3.5 metal bracket kit. Just remember - its M.2 SATA, it is not compatible with M.2 PCIe/NVMe. See the photos of the product for the keying on the slot that can be supported. StarTech also has a carrier for 2 or 4 M.2 SATA SS, if you need to have more M.2 SATA SSDs..

Did not work. The M.2 would not fully seat into the device. After more force than I was comfortable with is was almost in but the computer would not recognize it. The same M.2 fit and worked normally in another device.

The StarTech.com M.2 SATA SSD to 2.5in SATA Adapter (SAT32M225) is an absolute must-have for seamless SSD expansion. Its open-frame design and 7mm profile make installation a breeze, and the performance is nothing short of exceptional. This adapter has effortlessly transformed my storage setup, and I can't recommend it enough!

I used the two adapters in my Startech cloner usb 3.0 model and I got mixed results. I have cloned other drives, mostly all to upgrade without the full reload and have never had a failure. I cloned one Windows 10 drive so I could upgrade to a much larger SSD than what was supplied with the laptop and it worked, for about 16 hours. Then total crap and the drive didn't die, but got some serious corruption going. I ended up putting the old drive back in as I didn't format it yet, everything was cool. Next I cloned the data drive to upgrade to a bigger size and this worked without issues. The computer was not a Lenovo with extra hardware security or anything weird like that and I haven't tried again since. Overall the use of the adapters went well, easy to slide the drive in and secure it with the screw.

While they do state amongst their images and data that this is not the case, this is a heavily returned ityem for a reason. Make sure you aren't trying to use an NVME m.2 drive with it. That seems to require a different adapter with a more specialized connector than typical SATA.

These adapters made duplicating my M.2 NGFF drive a breeze. Simply mount the SSD into the StarTech Adapter and follow the instructions for your drive duplicator. In mine the cloning process took about 15 minutes total beginning to finish.

el adaptador es muy sencillo, una tarjeta que incluye sus tornillos para agregar la unidad m.2 en mi caso busque un adaptador con conectores Sata, hay que poner atenciòn a este detalle pues hay otros adaptadores que vienen con conector U.2 y el comun de las computadoras no son compatibles con este tipo de coneccion. Habiendo revisado previamente estos detalles , compre la unidad m.2 con conector sata y este adaptador con el que funciono inmediatamente, no se necesitan drivers ni nada complicado. Luego de conectada la unidad a mi motherboard, ya solo fue de clonar mi disco duro y reiniciar desde esta unidad. Todo funciono perfectamente. Quiero agregar una actualizaciòn sobre este producto. Quise agregarle un disipador de calor para mantener mas fresco mi ssd e intente con unos disipadores que yo tenia pero me encontre con el problema que con cualquier disipador, al colocarlo la base de este topa en la tarjeta, esto es debido a que el conector M.2 es muy bajo y casi no queda espacio, solo el M.2 encaja perfecto pero no permite agregarle un disipador pues este topa con algunos de los circuitos de la base de la tarjeta, creo que deberian tomar en consideraciòn esta observaciòn si piensan agregar un adaptador de estos.

古い機器を動かすのに古いノートパソコンを使用する事になり余っていたSATAのSSDを使用するために購入。 作りもしっかりしていて問題なく使用できています。

Utilisé pour mettre un nvme m2 Sata dans un acer V3-771G-32326G1TMaii. Fonctionne correctement et sans problème. Je précise pour ceux qui auraient des doutes : vous devez mettre un m2 sata, (par exemple : VERBATIM Vi560 S3 M.2 Sata) et non pas un m2 pcie(par exemple : WD_BLACK SN850X SSD).

ES MUY FUNCIONAL, BUENA CALIDAD Y FUNCIONA SIN PROBLEMAS

Das recht schnell angekommen gute Qualität leicht zu montieren, konnte es allerdings nicht benutzen, da Festplatte nicht kompatibel war. mein Fehler 🫢☺️👍

As described in specifications