Geekworm PCIe Metal Case P579 for Raspberry Pi 5 Support Top M.2 NVMe HAT X1001/X1004/X1003/X1015/X1000 & Raspberry Pi 5 Active Cooler

I purchased this for a Raspberry Pi 5 Network Attached Storage (NAS) project I was doing. I needed a well ventilated, sturdy case that had room for a NVMe SSD daughter card (hat), a heatsink for the SSD, an active cooler for RPi 5 as well as good access to all the RPi's ports. This case ticked all those boxes. Better yet, it's made of metal. It comes with all the screws and rubber feet you need for a quality finished case. The case is well constructed, sturdy and fits together seamlessly. Very happy with this case. Will buy more of this case in the future.

This case I bought to replace on that came in a kit from another company. I love the nice finish. The cooling is great and I have no issues using my active cooler which it fits along with my nvme hat. The space for the power button fits great. Putting it together was easy. Only downside is you have to take it apart to change out the nvme but that's only a few screws and more do to the hat then the case. Overall great case I would recommend to any of my friends. Which I have.

At first, I was delighted by the quality of the P579 steel case. It is stamped and folded from a sufficiently sturdy gauge of steel to resist flex. The case fits together well, and the holes align. There are no burrs on any edges, and the thick matte black finish is everything I could hope for. However, some minor issues soured my experience just a bit. The case arrived with the cover screwed on, the screws so tight that I feared the heads would strip out before they came loose. With channel-locks on screwdriver, I forced the screws out. I suspect paint choked the holes. Working the screws in and out a few times freed them up. If you encounter this problem, make sure your screwdriver is EXACTLY the right size for the screws. The small instruction card that comes with the case is all but useless, and the QR-code printed on the card is too small for my phone to read. Set the card aside and go straight to the Geekworm website. It was there that I discovered that the included screw & nut kit had extras of some parts, but was entirely missing the brass risers needed for the SSD hat. >>CORRECTION!<< In my discourse with Cindy Ding at Geekwork, I have discovered that the long risers shown in the Amazon Photo are NOT included with this case. Apparently, long risers come with the SSD board. The hardware actually included with the case is seen in another photo, and those are short risers. My confusion lead me to believe that parts were missing from the screw pack, when They Were NOT. Finally, the hole for the Pi-5's power button means you may need to mush your fingertip into the case to power up your computer. An flexible-membrane button over the hole would have been nice. But this is a small quibble; it shouldn't be a deal-breaker given the quality of what you get for the price. (I have fat fingers. I plan to glue an extinction onto my pi button so that it juts out beyond the case. Be careful if you try to do the same!) Conclusion: The P579 is a well made case at an affordable price. The good people at Geekworm in China were very responsive to my Emails. I LIKE a company that stands behind its products. For this reason, I give the P579 case four stars. (Thank you Cindy Ding!)

Nice little case for my Pi5. I have the x1001 hat with a low profile heatsink and a official active cooler in this case and it stays around 55 and 60 degrees celsius under load. This isn't terrible for a Pi5 pretty much loaded.

it will fit the rasperry pi 5 fan & pcie hat and it’s good quality finish. I got “let go” (aka fired) by HR after throwing it across the lab while “speaking in tongues” when my experiment failed. It fired right up when I got home... … I went MENTAL when they called later telling me they’re withholding my paycheck pending “Damages”...

No issues so far, good value for money, sturdy case.

I like the case. Ease to place the pi board in and secure it. I do wish there was a button the would stick out for the on/off.

If you're running a Raspberry Pi 5 with the Geekworm X1001 NVMe HAT, steer clear of this case. The ribbon cable included in the X1001 kit is unshielded (at least the one I bought within the last couple months), and the case geometry brings it into direct contact with the metal enclosure, causing an immediate short. I attempted a workaround with electrical tape on the cable, which held up for about a month before the Pi started crashing randomly. Once I removed it from the case entirely, everything ran normally again — confirming the case was the culprit. The root cause is a design mismatch: this case simply wasn't engineered with the X1001 HAT clearances in mind. I've since moved to a different case and have had zero issues. Bottom line: If you're using the X1001 HAT, look elsewhere. This case will cost you stability and potentially hours of debugging what looks like a software or storage problem.

Fitted perfectly Very happy

This product is far superior to the official case. It accommodates the geekworm NVMe adapter as well. It can accommodate the official cooler. It's well built out of solid metal. Looks great and is vented to allow a massive amount of passive cooling. It should be a fairly simple thing to just drop a fan on the top of this to help pull the air through. There's loads of events for it to get through. Assembly was relatively straightforward. It is fairly self-evident how it should be assembled. I really appreciate the standoffs that raise the pie above the case and still leave room for everything else that needs to go inside. I also love that the power switch is readily accessible and that the power light from the pi itself and the NVME adapter busy light are very visible. In summary, this case is an excellent price, it's well designed, looks great and I'm extremely happy to have it to replace the official case that I was given that simply couldn't accommodate the geekworm NVMe adapter and really didn't do what was needed

Compré hat y ventilador de la misma marca, mejor adaptación no hay perfeto

The circulation of the air is obstructed by any additional hat, it raises the core temperature easily. But the case is sturdy with all the parts.