1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT-891

I have an older saw, so I had to change out the choke arm. Other than that, it was a perfect fit, and works great. I have a 2nd saw that is doing the same thing. I got a 2nd one for that saw.

My Ramblings Been a while since I tuned up this chainsaw and it has begun to start hard and run rough.. So, let's just replace it all, because it's cheap to do so. To the Point or TL;DR Two surprises: Primer Bulb Intake is on left side; however, Not in the way of throttle linkage. Throttle on both left and right side of carb, also, doesn't interfere with anything. It wasn't missing any pieces or parts. Chainsaw started after some priming and a four good pulls. Have your screwdriver ready to adjust. Adjusted it and runs smoothly. The carb didn't change my chainsaw it into a new one, but it made it run smoothly for the first time in a while... So worth $18. The Bad Stuff None so far Who May Use/Like It Those needing a tune up on their very old, but still useful Poulan 2150. Me Final Thoughts Go ahead and buy yourself a new chain while you're at it. My old saw running smoothly again. I could use a little of that myself. That's my story and I'm sticking to it. Hope it helps! All the best, Just Benjamin Reviewed: Brand: Harbot Cost: $17.88 at time of review. 1950 2050 2150 Carburetor For Poulan Chainsaw Parts 1900 2055 2175 2350 2450 2550 262 Wild Thing Chainsaw Replaces 545081885 530069703 C1Q-W8 C1Q-W14 WT 89 891 WT-324

I got this carburetor to replace the original on my Poulan 2375 chainsaw. It was listed to fit my model, but I found that it differs from mine, and in my case required a different part to fit. The kit has everything needed for a fuel system maintenance. It comes with a fuel filter, two sizes of fuel hose (small fuel feed, large fuel return), a new priming bulb, an air filter, a spark plug, and the carburetor with the gasket. Such a great price for everything included. I had some trouble feeding the fuel lines into the holes, but got it eventually. The addition of a fuel filter is nice as my saw never had one originally. The carburetor fit just like the original; however, when I went to assemble the air filter, the housing didn't fit this new one. My saw must be an earlier version of the model number, because this replacement has a different Choke Control Rod. While the new carburetor has a better choke setup, the air filter housing isn't the same. I had to get a replacement air filter housing that has a bigger relief cut out to allow for the larger new one. So check out your old carburetor when purchasing this upgraded one. Assembly was pretty easy after getting the hoses installed, and the saw started right up when I was done. I only had to make a small adjustment to the Lower Speed/Idle setting and I was good to go. I really like this upgraded carburetor kit and only wish I'd done it sooner.

Various extra parts Good fit As described Great Great value

I needed this for a Poulan Wild Thing 2375 that had the early Walbro WT-324 shown in the second picture, with both fuel lines on the same side. This carb, as shown in the listing, has one fuel line on each side, and the choke linkage is a little different. I had my doubts it would work, but the throttle linkage is the same, so that hooked right up, and I had no problem with the choke side either. It comes with new fuel lines, so you have plenty to route it the new way, and everything fits without having to alter, bend, customize, or otherwise mess with. Simple and effective replacement. Just make sure you know the fuel line routing, because when they crumble taking off the old carb, and you don’t know where they go, it’s not fun when you hook them up wrong. Simple to adjust, saw runs great!

I had to modify the carb to work on my chainsaw. It’s a 1950 model wood shark. The choke was different and the air box would not fit. So I had to swap out the choke valve rod with the old one. Also I the fuel supply and return is on the same side on the old one and the new one was one on one and the other I will say that I do believe mine must be a rare breed bc I was unable to find anything that looked like mine online. And once I modified it it started and is still running without any adjustments. I believe this is a good carb but there is some discrepancy about it fitting my model

I have an old Craftsman chainsaw model 358.350802 and for whatever reason, of the seemingly 100's of different and similar model #'s, I cannot seem to find hardly anything for MY SPECIFIC model #. The saw had not been started in over a decade I'm sure. It was my deceased father in laws chainsaw and I really wanted to get it running. Through cross reference of similar model #'s and comparing the photos on the product pages with the equipment I have, I decided to take a chance on this kit, even though Craftsman and their models are not even mentioned in the product description. I got the kit and aside from the primer bulb, (which I knew was different) everything fit and worked great. I got the fuel lines put in and put in the new carburetor and fired it up and was cutting down trees in minutes. Really happy to find this product that was a perfect replacement for my old Craftsman when I could not find anything that was supposed to be an exact replacement. Very Pleased.

Their is everything you need to get Poulan running again in this kit. I admit that replacing fuel lines can be intimidating but not impossible. As they show you online, You cut part of fuel line in half and put in hole in case. Then pull fuel through to proper length with needle nose pliers. They give you more then enough fuel line to complete job. One thing to remember take pictures of fuel line routing with cell phone first if you forget fuel line routing is also shown on line. No luck needed to complete this repair.