SPACEKEEPER Workbench Casters kit 920 Lbs Retractable Casters Heavy Duty Bench Caster Wheels Side Mounted Retractable Workbench Wheels Designed for Workbenches Machinery & Tables, 4 Pack

When I got it, I ran a test by mounting it on a 2x4, it worked fine. Three weeks later after I built the 2'x4' woodbench, I installed all four legs. It works very well, solid and easy to operate it. But, two comments about this product: - The installation manual is a joke, useless in one piece of paper with simple drawing. Look their product pictures, that's more detail of how to do installation. -2nd, the template is1/8" off, too short, don't follow it. Use the real plate will get the job done right.

Works just as described. Instructions are barely usable, but it’s fairly easy to figure out. Lifts my heavy workbench with ease. Highly recommend.

I picked up this 4-pack of casters back in December for $34.84 to make my heavy workbench mobile. My bench comes in around 200–250 pounds fully loaded, and these have no problem supporting the weight and keeping things stable. One of the best parts is how easily they retract when I have the bench where I want it. Then when I need to move it, I can just re-engage the casters, and I’m rolling again. Installation was simple — they include a template, which helped a lot. That said, I did end up shifting the mounting position slightly past the recommended spot to better fit my bench setup, and it worked out great. Only real con is that it takes a bit of effort to get the bench moving exactly in the direction I want — especially if I’m working in a tight space. Usually, I just walk around to the other side and guide it from there, and it’s no big deal. For the price and what these can handle, I’d say they’re absolutely worth it. Makes the workbench much more functional without compromising stability.

Great, sturdy coasters, easily to lock and unlock . Smooth swivel. Easy installation with necessary screws, bolts and ranges included in each kit.

I tried to use the wheels to occasionally move around a tire machine. No problem with the installation. Used my own nuts and bolts, and drilled directly into the steel of the machine. Pushed the levers to raise each wheel, everything ok. Then I rotate the machine, everything ok, until I bumped the the side of a carpet runner on my concrete floor. PROBLEM. 3 of 4 wheel studs bent. POOR design, all the weight of a wheel is on the single hex part of the wheel stud. That might be 5/8"? Wheel metal must be made of very soft steel, Chinesium, probably. My wheels bent , yours might , too. That's when I found some used all steel wheels where the weight would be distributed over a much greater area, at least a 2" radius, each. So I spent about $40 to use the bracket/lever part, Junked the rest, and added my own wheels. Now , No problem. So Be aware that the poor design of the small stud area can't possible be rated for the 920 pound weight of a set of wheels. Unless you never bump into anything. If you're trying to move around something much lighter, it's probably fine. 920 pound rating , for the whole set, is B.S.

Very reasonably priced and does exactly what you expect. It comes with a template that makes it very easy to install. No measurements needed. The orange rubber tip does come off easily and I simply removed them. I guess you could glue them on but it doesn't affect its performance and function. One thing to keep in mind is that they do stick out and will infringe in the space next to your bench legs. Yes, I would/will buy again.

I didn’t even know I needed these until my husband bought them for my work bench that was stationary. Install was a breeze with the provided template. Once installed it is easy to use. Push down for using the wheels that locks the wheels in place so you can move your item around. When you want to be stationary lift the levers. I do recommend initiating two of the same sides at the same time (if you can) or you will have some weird tipping from corner to corner. The castors move smoothly across my garage floor. Barely adds height to existing work bench so there is no worries if you think it'll be raised to high. Its perfect.

I managed to get these installed and working, no thanks to the bad instructions. The drawings don't represent the actual parts, so I installed the caster plate upside down. If I had gone back to Amazon and looked at the illustration, I would not have made this mistake, but who does that after you have ordered and received your product? The instructions have you completely assemble these before mounting them on the leg of your table. Do not do that. (photo #2) the caster and mechanism block easy access to the mounting screws. I made a block of wood and clamped it to the leg to set the height without tedious measuring while sitting on the floor. This worked great. On my first try, the caster had rotated inboard and the lever will NOT work if it does that. (photo #3) I thought the height was wrong, but determined that if the caster is rotated outward it work with the instructions mounting dimension. I did not have the issue of twisting the screw heads off, but agree with one reviewer's comment that the bolts could be a few mm longer. I also have not experienced broken bolts or bent mechanisms and one of my benches is extremely heavy. It appears that these will work and I don't expect to be moving this stuff around often so I think they are OK. I have installed two sets and am considering a couple more.

Me gusto el producto.

Herrajes 7 de 10 Llantas 10 de 10 Gomas 3 de 10 ( las tuve que pegar con silicona) Tornillos 3 de 10 (se nota que son de baja calidad) Pijas 1 de 10 (se barren al momento de instalar, utilice otras pijas de mejor calidad) En resumen, compren de otra marca.

Works perfectly. Heavy duty materials, can lift a lot of weight. However the instructions are somewhat contradictory and images unclear. First construct the bracket (silver piece should have ridges up), as in my photograph. Then cut a 2.4" high piece of wood and clamp it to the base of the leg. Install the bracket above that piece of wood. Only then attach the wheel to the bracket. Also, as others note, the orange/red step end falls off because the manufacturers used the wrong kind of glue (it has to attach plastic to metal). I re-glued with a two-part epoxy glue, then clamped it on for a couple of hours and now it's on solid.

Attached this to a welding table and it works as expected but would prefer a version with metal wheels for use in a welding shop where small pieces of sharp metal end up on the floor to dig into the plastic wheels. The red plastic caps comes off the first time you use your foot to crank down and raise the table.