Tyger Auto Fender Flare Compatible with 2002-2008 Dodge Ram 1500; 2003-2009 2500 3500 8' Bed, Fine-Textured Black Paintable Factory Style 4pc | TG-FF6D4208

Well packaged and protected, and unbelievably, they actually provided extra hardware! When I installed them, 3 fit nearly perfectly, and they look amazing on the truck. One, however, fit badly. I contacted customer service and was treated extremely well. Within a very short time I was contacted by email for a couple of pictures and my address. Soon after, I was told a complete new set was on the way. This is customer service rarely seen these days. Putting them on was as easy as could be, and I can't imagine anyone not being able to do it with basic tools. Both front flares fit like they were OEM. The back are not quite as perfect, but still very good. They also cot $100 and not $800 like the OEM flares! I would absolutely buy these again.

The flares fit fine and don't have any gaps. I used additional rubber trim to fit the flares against the body panels better. Pretty easy to install. Two small issues though.Be every careful when moving the flares around if you are in the driveway. If any part of the flare drags on the pavement there WILL be scuffs on the plastic. I wasn't paying attention while installing the rubber trim and two flares had bad scuffing from rubbing on the pavement. Plastic must be really soft. I plan on using some Back to Black to darken the scuffs.Second issue is if you have a Diesel engine the Cummin's emblems on the front fender will have to be removed as they are in the way of the flares. The emblems came off okay but it was an unexpected task to make the flares fit. Would have been nice to have that noted in the description prior to purchase. As the emblems are intact I will just reattach them higher on the fender above the flares.

These flares are fantastic. Easy install, with provided hardware, and I think they look great! They provided enough coverage to hide the "fender rot" on my 03 Dodge Ram. I sanded down the areas, and gave them a good coat of Rust-Oleum first. I installed these alone, in well under an hour. I did drill one hole on each rear to help tighten them up a little, but all other screws went in the factory holes. No rubber seal was provided, but they fit well without it.

Did ok, looks good. Not the tightest of fits, put a bit of black chalk to help seal against water.

These fit perfectly. Not too big or sticking out like other makes.

Been looking at trucks for my stepson for months. I live in CT so nearly everything we found was rusted and rotted. Found a nice 2004 Dodge Ram 1500 with a perfect frame and bed crossmembers. But... it had the typical rear fender rot. My picture shows the worst side, the passenger side. These are about 4" high so it covered the rot up well! My stepson did the installation himself, and he is a novice wrencher. I feel like anyone can do this!! He did mention the top screw on both back fenders needed to be drilled, but also said they are very secure as it was. I will end up drilling those holes for him later. I highly recommend this set of flares, especially if you're looking for an OEM look, and not those gaudy, ugly flares that have the visible screw holes on the top of the flares. those are horrible looking.

These are well made and fit my 08 Dodge Ram like a glove. They were easy to install and at a great price point. Would recommend them to anyone looking for fender flares.

Overall, pretty easy to install with clear instructions. Took me about two hours to do all four with very little hiccups. For the price point, these were a pretty good choice. The main reason I bought them was to cover up rusting fenderwells.

Exelente le quedaron a la camioneta

good quality fender flairs easy to put on , does not come with rubber edging. use vice grips to hold each flare on , cut a v notch in the rubber edging as shown in pictures. was the only method could come up with without cutting the edging in 2 pieces. affordable option to hide dodges rust problem with their boxes . mine had holes but disappeared with these flairs

These flares are fantastic. They DO NOT stick out so they look great with a factory tire size. The rear install was a breeze but the fronts we're a little more difficult. When you install the fronts either take the wheel off or just turn your wheels to allow you more space. The fit is 9/10 and the install is around 7/10. They look factory and hide any rust if you it. Comes with all hardware and of course ships fast thanks to amazon. Would recommend to anybody who asks for sure. A partner to install will help immesnsely.

Fender flares were easy to install and covered all the visible rust around the wheel wells on our truck. They fit well and look good. We used some car door edge trim to finish the edge that goes next to the truck. It looks great and will stop any rubbing on the painted surface and seal the edge better. This kit could use more u clips and also should come with the door edge trim for a few dollars more. Very Happy with this purchase.

Satisfait