HCDC RPi GPIO Status LED & Terminal Block Breakout Board HAT for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B

I used this breakout board in my Raspberry Pi–based oven controller, and it made wiring and debugging way easier. The screw terminals keep connections secure and clean, and the LED indicators on each GPIO pin are incredibly helpful for monitoring pin state at a glance—no more guessing if your code or wiring is working. It plugs directly onto the Pi's GPIO header and includes clear pin labels, so setup was fast and error-free. Perfect for permanent installs or prototyping where reliability and visibility matter. Highly recommend for any Raspberry Pi GPIO project—especially if you’re driving relays, sensors, or building something like a custom control panel. This board makes it way easier to troubleshoot and maintain.

Since Amazon likes to combine reviews for totally different products, this review is for the HCDC RPi GPIO Status LED & Terminal Block Breakout Board HAT. I'm not sure why people complained about putting this board in a case. It is pretty obvious that many HATs will not fit inside a closed case. This board will work with a male to female 40-pin flat extender cable if you remove the two plastic posts on either side of the connector. You really don't need those posts except to permanently attach it to the base board or another HAT. The connector works pretty well as a "foot" and you can leave the other posts for feet on the other side. I am using a Compute Module 4 with a WaveShare IO baseboard. This has plenty of clearance above the Waveshare heat sink and Compute Module 4. Although I can't close the case, I could file a slot in the cover and use a ribbon cable. My only minor complaint is that the signal designations on the terminal blocks are ordered differently than for the connector pins. I haven't figured out if there is a system to it, but they seem quite random. In some cases the label is the GPIO pin and in some cases it is the usual function, like "TX' or "RX". Probably it wasn't possible (or easy) to make a layout on the terminal blocks to match the connector pin ordering. With a little bit of care in finding the right connection, this provides all the signals. What impressed me was the construction. If this is built by hand, it was done very well. There were no cold solder joints, splashes or burnt lands from using too much heat. It actually looks like it was put through a wave soldering or surface mount soldering machine. The plastic posts could have been metal, but they're good enough being plastic. For the price, this board is a good value. I'm porting an OS to the Compute Module 4, and this board has saved me from hanging LEDs off of my board. It is also nice to see the serial port TX and RX data to at least know of the signals are reversed (one LED on instead of 2).

This is an excellent little GPIO breakout board you can attach to your pi 4. Arrived fast. Packaged okay.. to be honest the packaging was all torn up and I was surprised it wasn't broken in shipping but it worked. It's hard to actually damage an item like this I think unless you overdrive it. I attached it to my pi and an Adafruit 240x240 LCD display then wrote a matrix style screen saver in python and it works flawlessly. I think I read it had led's in the amazon description, but seeing it's leds light up looks great and is actually educational. I bought this one for my pi 4 dev machine and am so impressed I will likely buy a couple more for other pi 4s I use in python automation code development. I couldn't be happier with purchase. Highly recommend if you're into things like this.

It functions fine and does exactly what it suppose to do which earns it 5-stars. BUT, I found two aspects to it to be confusing: 1) The terminal connections don't have any correlation to the 40-pin connector & LED layout on the right side. You can have pin 1 located on the 3rd row of terminal connections and pin two can be on the 1st row, pin 3 next to it and pin 4 on the 4th row. Very confusing. 2) The led indicator lights for the GPIO connections turn on when the circuit is Open and turn off when the circuit is Closed. Like turning a switch off to make the like turn on and vice versa. Otherwise, it works fine once you understand its quirks.

This provides a light for every output, plus access to the output with a screw terminal rather than having to make a header for connection. It is a step closer to installation in the final product without the need for weaker connection means, plug in socket with a wire is not a reliable way to implement a project. With this, you can test outputs by sight, and simulate inputs with simple means. Well worth the money. After the first arrived, I ordered three more.

Very useful during the development cycle of a project using the Raspberry Pi 4 Model B.

I used the board in this case to make accessible the GPIO ports of the Raspberry PI 4B-8. This board interfaces perfectly in any situation where the GPIO pins array is accessible. This little board is a no-brainer. Don't think, just buy it. :-)

I bought this thinking that it might be handy to have around but instead found this breakout board to be so much better than I expected. It is so nice to have screw terminals for all GPIO and power pins. Each row has power and ground plus a row of GPIO connections. Two rows have 5v and two rows have 3v. The only thing I would add would be to put 5v and 3v on each row. The screw terminal blocks are well built and grip the wires firmly. The board fits the Raspberry Pi perfectly and comes with stand offs for mounting the breakout board to the Pi. I highly recommend this product.

Way better than using the pins