Cable Matters 100-Pack Cat 6A Shielded Pass Through RJ45 Connectors, 50µ Gold Plated, Max. Wire OD 1.19mm (Cat6A Ends/Shielded RJ45 Connector/Ethernet Ends) for Solid or Stranded S/FTP Cable

Bought these to go with True Cables clear cut to fit strain relief boots. So far I haven't had any bad terminations with 23awg cable. The boots thankfully fit inside with ease as the cable itself is a cat6a shielded riser cable that measures a smidge over 7mm thick. The outer cable sleeve will not fit inside but that is alright since the strain relief boots locks inside the plugs and I would rather have the shielded foil of the cable to fit snug inside.

Works as designed

When crimping these with a normal pass through crimper, the RJ45s have too much excess plastic that prevents the crimper tool from cutting all the wire off. This leads to excess wire hanging out the end of the RJ45 and the cable won't sit properly in a NIC. You can use a knife to trim some of the excess wire. However, even then, these don't work great! The actual connections to the wires are very shoddy. They all tested out fine with a cable tester, but not one single cable would give me more than 100Mbps FE. I had to spend many hours reterminating every single cable on the site with higher quality terminations.

It works as it should. Great value. YES! I'm that guy who thought I could crimp a Cat6A, CMX cable to a cat6 pass-though connector. Well, the gauge was too big, so I bought these and it worked! I tested this with a Fluke tester and got 1gb with a green checkmark.

works for application

I bought this name brand after hearing some of the cheapest ones had tolerance issues fitting into ports. These have made CAT 6 UTP wiring very easy, paired with a through-plug style ethernet crimper that cuts off the excess. I'm doing 23awg solid copper with no issues! I can't say if 6a/7/8 will fit, with their larger shielding. It's worth it getting these rather than fumbling with the old kind.

I had a lot of misfires with these. The description says 6/6a. I maybe got 1 out of 10 to work with cat6. Cat 6a, much better luck. Would have given more stars if they dropped the assertion you could actually use these with any kind of confidence with cat6 because you cant. These are only for 6a. I also had a number of them not work with 6a, but at least the failure rate wasnt 90%.

Make sure you get the right type - Cat6 vs Cat6a - there is a difference. Nice quick and easy with the full pass through, cables tested well after - at least those where I didnt screw up the wire order ;)

My colleagues were using the cat6A RJ45 Connectors and found that it is not working. We had to try many attempts before only a few will work. Please check on the quality of the RJ45 as we cannot use even a single piece now as we are concerned about the quality.

Arrived, not tested yet but they look okay

Ottimo

Super faciles à utiliser comparé aux anciens connecteurs qui nécessitaient de couper tous les brins à une longueur spécifique et ensuite les aligner correctement au travers de celui-ci. Avec ces connecteurs 'Pass-through' il suffit de retirer l'isolation externe du câble, généralement je retire entre 3 et 4 cm, et ensuite à peu près arranger les brins et les enficher au travers du connecteur. Vu qu'ils traversent celui-ci, on peut vérifier aisément qu'ils soient bien arrangés avant de sertir le câble pour de bon. Petite astuce, je coupe les brins avec un certain angle, cela me permets de les enfiler plus aisément dans le connecteur. Le seul point un peu négatif, ces connecteurs nécessitent une pince à sertir spécifique, mais celle-ci ne coûtant que 20-30€, le prix à payer vaut largement le temps gagné. Je suis déjà presque à la fin de ma première boite, j'en re commanderai sans hésiter !

Tiene buena calidad y facil terminacion